Skip to content

Polished Concrete

Concrete Polishing in Marietta

A slab that is ground, densified, and sealed to a specified sheen, durable, clean, and finished to last.

  • Written Estimate
  • Surface-Prep Checklist
  • Documented Handover
A modern minimalist living space featuring a grey upholstered armchair and a small coffee table on a concrete floor, with a textured grey concrete wall and a wooden panel.

What Goes Wrong

Where concrete polishing fails, and how the right process avoids it

Skipped Grit Steps

Jumping grit levels leaves a visible scratch pattern in the slab that no sealer can hide.

Full Grit Sequence

Each pass runs in order from coarse to fine, removing the previous scratch pattern before moving up.

No Densifier Applied

Skipping the densifier leaves the concrete porous, so the sealer sits on a soft surface and wears fast.

Mid-Sequence Densifying

A chemical densifier is worked in mid-sequence to harden the matrix before the final sealer goes down.

Unassessed Slab Damage

Starting to grind without checking cracks and pits means repairs happen late, disrupting the grit sequence.

Condition Check First

The assessment covers hardness, cracks, stains, and moisture before any grinding begins, and repairs come first.

Missed Edge Work

Perimeter zones the floor machine cannot reach are left rough, making the finish look patchy near walls.

Handheld Edge Grinding

A handheld grinder works the perimeter to the same grit level, keeping the finish consistent to the wall.

Scope of Work

What concrete polishing covers

From a basic grind-and-seal to a high-sheen finish, the scope depends on slab condition and the finish level you specify.

  • Garage Slab Polishing

    Ground and sealed to handle vehicle traffic and oil exposure.

  • Basement Floor Polishing

    Moisture-checked and sealed for below-grade conditions.

  • Commercial Floor Polishing

    High-sheen finish rated for heavy foot traffic.

  • Aggregate Exposure Finish

    Coarser grind to reveal the stone in the slab.

Grind, Densify & Seal

How concrete polishing works and whether your slab is a good candidate

Polishing refines the slab itself rather than covering it, existing cracks, stains, or patches may still show, and the assessment stage is where that gets confirmed.

The installer starts with a slab condition check. Marietta garages and basements vary widely in concrete hardness, crack history, and surface contamination, and those factors determine which grit to start at and how much aggregate will be exposed at the finished level. Cracks and pits are repaired before grinding begins so the diamond pads are working on a consistent surface.

Diamond abrasive pads progress through a coarse-to-fine grit sequence, typically starting at 30 or 50 mesh and finishing at 400, 800, or higher depending on the specified sheen. Each pass removes the scratch pattern left by the previous grit. Edge work with a handheld grinder covers perimeter zones the floor machine cannot reach, keeping the finish consistent to the wall.

A chemical densifier is applied mid-sequence to harden the concrete matrix and reduce porosity. This step improves abrasion resistance and makes the final sealer or stain guard more effective. Once the target finish level is reached, the installer performs a moisture check and applies the sealer. You receive a written record of the grit progression and materials used.

Request Your Estimate

Why Choose Us

Why choose us for concrete polishing in Marietta

Every job is backed by written documentation at each stage, from the first estimate to the final handover.

  1. Itemized Written Estimate

    You receive a written estimate listing materials, grit progression, and cure times before any work is scheduled.

  2. Surface-Prep Checklist Included

    Every estimate includes a checklist covering grinding, degreasing, and crack repair so nothing is left unconfirmed.

  3. Documented Handover

    A curing inspection is completed at the end of the job, and a written record of materials used is handed to you.

  4. Scoped & Quoted in Writing

    Every assessment accounts for Cobb County slab conditions.

  5. No Work Booked Without Agreement

    Nothing is scheduled until you have reviewed and agreed to the written estimate, no surprises on scope or cost.

A stylish and spacious hallway featuring grey painted walls with white marble wainscoting, white doors with ornate frames, and a patterned terrazzo floor.
A tradesperson in yellow safety boots stands in wet, self-levelling screed, with a hose pouring more material and a levelling tool visible.

How It Works

From enquiry to finished floor in three steps

  1. 01

    Submit Your Details

    Tell us about the slab, size, condition, and finish level, and we’ll schedule the right assessment in Marietta.

  2. 02

    Receive a Written Estimate

    The assessment covers the slab and produces an itemized written estimate covering materials, grit sequence, and cure times.

  3. 03

    Grinding, Sealing & Handover

    The installer completes the full grit progression, applies the sealer, and hands over a written record of all materials used.

Pricing Estimates

Typical Concrete Polishing Prices

JobTypical cost
Basic polish$3-$6 per sq ft
Standard polished concrete$6-$9 per sq ft
High-gloss polish$9-$15 per sq ft
These prices are estimates and often vary with the condition, size and scope of each job. Message us for a free, no-obligation quote.
See all prices

Common Questions

Questions about polished concrete floors

  • How do I know if my concrete floor is in good enough shape to be polished?

    Most concrete floors can be polished, but the slab needs to be structurally sound with no active heaving or deep delamination. Surface cracks, stains, and minor pitting are common and can be addressed during prep. The assessment covers your floor before work begins and flags anything that needs repair first.

  • Will cracks, pits, or stains still show after polishing?

    Small cracks and pits are filled with cementitious filler or epoxy grout before grinding, so most disappear or become far less visible. Deep or wide cracks may still show a faint line after polishing. Oil stains that have soaked deep into the slab can lighten but may not vanish entirely, your estimate will note which repairs are needed upfront.

  • How smooth and glossy will my polished floor look?

    Finish levels run from a flat matte (around 400-grit) to a high-gloss mirror finish (1500-3000 grit). The final look depends on the grit sequence used and whether a densifier and guard coat are applied. The written estimate confirms which finish level suits your slab’s aggregate exposure and your intended use.

  • How much grinding and prep does my floor need before polishing?

    Every job starts with a surface-prep checklist covering grinding, degreasing, and crack repair before any polishing pass begins. Floors with coatings, adhesive residue, or heavy contamination need more aggressive initial grinding. The written estimate you receive will specify the prep steps and grit sequence required for your specific slab. See concrete surface preparation for more detail.

  • How long will the concrete polishing take?

    A straightforward residential floor of 500-800 sq ft typically takes one to two days. Larger commercial spaces or floors needing significant crack repair and multiple grinding passes take longer. Your written estimate will include a timeline with each phase, prep, grinding passes, densifier application, and final guard coat, so you know what to expect.

  • How long will my space be out of use during the work?

    Light foot traffic is usually possible 24 hours after the final guard coat is applied. Full use, furniture, vehicles, or heavy equipment, typically requires 48-72 hours. Cure times vary by product and are documented in your written estimate so you can plan around them.

  • Is polished concrete worth it for my floor?

    Polished concrete is a permanent surface, not a coating that peels or needs reapplication every few years. It handles foot traffic, forklifts, and cleaning chemicals without degrading. For spaces where durability and low maintenance matter more than a soft underfoot feel, it typically outlasts coatings and overlays on a cost-per-year basis.

  • What are the downsides of polished concrete?

    Polished concrete is hard underfoot and can feel cold in winter without radiant heat. It is also slippery when wet unless a slip-resistant guard coat is applied. Repairs to a polished surface are harder to blend invisibly than repairs to a coated floor, so addressing cracks before polishing matters.

  • Which areas do you cover for Concrete Polishing?

    We cover Concrete Polishing in and around Marietta, including Downtown Marietta, Cobb County, Atlanta, Fulton County and Cobb County. If your area isn’t listed, send us a quick message to check.

Get an Itemized Estimate for Your Floor

Tell us about the slab and we’ll schedule an assessment and quote materials, grit progression, and cure times in writing.

Request Your Estimate