Skip to content

Slab Correction

Self-Leveling Concrete Overlay in Marietta

A flat, bondable slab surface without tearing out the existing concrete, corrected and finished in place.

  • Written Estimate
  • Surface-Prep Checklist
  • Documented Handover
A tradesperson in yellow safety boots stands in wet, self-levelling screed, with a hose pouring more material and a levelling tool visible.

What Goes Wrong

Why some overlays fail and how the right approach holds

Skipped Moisture Check

Vapor rising from a slab-on-grade floor breaks the bond between the overlay and the concrete beneath it.

Moisture Test First

A moisture check before any primer goes down confirms the slab is dry enough for the overlay to bond and stay bonded.

No Bonding Agent

Pouring a cementitious overlay directly onto bare concrete without primer leads to delamination under foot traffic.

Primer Before the Pour

A bonding agent coat gives the overlay a mechanical connection to the slab, so it does not lift or separate over time.

Unrepaired Cracks

Bridging the overlay over active cracks transfers slab movement into the new layer, causing it to crack in the same spots.

Fill Cracks Before Overlay

Cracks and voids are filled and allowed to cure fully before the self-leveling mix is poured, so movement does not transfer up.

Wrong Thickness Applied

Pouring the overlay too thin over deep low spots leaves weak areas that chip or hollow out under regular use.

3/16 to 1/2 Inch Range

The installer sets the pour depth to the slab’s actual low spots, typically 3/16 to 1/2 inch, so coverage is even and structurally sound.

Scope of Work

What a self-leveling overlay covers

From garage slabs to basement floors, the overlay corrects surface conditions before any finish is applied.

  • Crack Repair Before Pour

    Cracks filled and cured before any overlay is mixed.

  • Moisture Barrier Option

    Applied where slab vapor readings are elevated.

  • Polished Concrete Finish

    Overlay ground and polished once fully cured.

  • Flatness & Bond Testing

    Confirmed before any finish work begins.

Slab Correction Service

How a self-leveling overlay corrects an uneven slab without replacing it

Settled or pitted concrete in older homes can be corrected with an overlay pour rather than a full tear-out.

The process starts with a slab condition assessment. The installer checks for active cracks, low spots, and moisture, Marietta’s climate variation stresses slab-on-grade concrete seasonally, so a moisture check before overlay application is not optional. Cracks and voids get filled and allowed to cure before any overlay material is mixed, so the new layer does not bridge over unstable areas.

A bonding agent and primer coat go down next, giving the cementitious overlay a mechanical connection to the existing slab. Without this step, the overlay can delaminate under foot traffic. The self-leveling mix is then poured and spread using a gauge rake and spiked roller, allowing it to seek its own level across the floor.

Once cured, the overlay surface can be ground smooth, polished, or left as a base for a protective topcoat. Flatness and bond testing confirm the layer has adhered before any finish work begins. The installer documents the overlay thickness and materials used so you have a full record of what was applied to your floor.

Request Your Estimate

Why Choose Us

Why request a self-leveling overlay estimate in Marietta?

Every job follows a documented process from first assessment to final handover.

  1. Itemized Written Estimate

    You receive a written quote listing materials, overlay thickness, and cure times before any work is scheduled.

  2. Surface-Prep Checklist Included

    Every estimate comes with a checklist confirming grinding, degreasing, and crack repair are completed before the pour.

  3. Curing Inspection & Handover

    A final inspection confirms bond and flatness, and you get a written record of what was applied to your slab.

  4. Scoped & Quoted in Writing

    Every assessment accounts for hands-on experience with Marietta slab conditions.

  5. No Work Booked Without Your Sign-Off

    The estimate is reviewed and agreed before any installer is scheduled, so there are no surprises on the day.

A stylish and spacious hallway featuring grey painted walls with white marble wainscoting, white doors with ornate frames, and a patterned terrazzo floor.
A tradesperson in yellow safety boots stands in wet, self-levelling screed, with a hose pouring more material and a levelling tool visible.

The Process

From first enquiry to finished floor in three steps

  1. 01

    Request Your Estimate

    Tell us about your slab and we schedule an assessment of the floor and quote in writing.

  2. 02

    Prep, Prime & Pour

    The installer completes the surface-prep checklist, applies bonding primer, then pours and spreads the overlay.

  3. 03

    Inspect & Hand Over

    A flatness and bond check confirms the result, and you receive a full written record of the completed work.

Pricing Estimates

Typical Self-Leveling Concrete Overlay Prices

JobTypical cost
Thin leveling skim$3-$5 per sq ft
Standard self-leveling overlay$5-$8 per sq ft
Thicker overlay for damaged slabs$8-$12 per sq ft
These prices are estimates and often vary with the condition, size and scope of each job. Message us for a free, no-obligation quote.
See all prices

Common Questions

Questions about self-leveling concrete overlay

  • Can self-leveling concrete go over my existing concrete slab?

    Yes, in most cases it can. The slab needs to be structurally sound, free of active moisture, and properly prepared, ground, degreased, and with cracks repaired, before the overlay is poured. A slab that is crumbling, heaving, or saturated with moisture is not a good candidate without remediation first.

  • Can you just pour self-leveling concrete and be done?

    No. Surface prep is the most critical step. The slab must be ground to open the pores, degreased to remove contaminants, and primed so the overlay bonds correctly. Skipping prep is the leading cause of delamination. Pouring is the quick part; everything before it takes the most time.

  • Is concrete resurfacer the same as self-leveling concrete?

    They are related but not the same. A concrete resurfacer is a thin, trowel-applied coating used mainly to restore appearance on a flat slab. Self-leveling concrete is a flowable compound that finds its own level, making it the right choice when the floor has dips, slopes, or height differences that need correcting before a finish is applied.

  • What are the downsides of a concrete overlay?

    An overlay is only as good as the slab beneath it. Pre-existing cracks can telegraph through over time, and poor prep leads to delamination. Overlays also add height, which can conflict with door clearances or adjacent flooring transitions. None of these are dealbreakers, but they require planning before the pour.

  • Will self-leveling concrete bond well to my old floor?

    Yes, when the slab is properly prepared. Grinding opens the concrete surface, degreasing removes oils and residue, and a bonding primer locks the overlay in place. Every job includes a surface-prep checklist covering all three steps, and a final curing inspection with documented handover confirms the bond held.

  • Will cracks in my old slab come back through the overlay?

    Active or structural cracks can reflect through an overlay over time. Dormant hairline cracks are filled and stabilized before the pour to reduce that risk. The pre-pour checklist includes crack repair, but any crack that continues to move due to settling or thermal shift may eventually show through a rigid overlay.

  • Can self-leveling concrete fix an uneven floor, or do I need a different repair?

    Self-leveling concrete is the right tool for floors with low spots, dips, or gradual slopes, typically correcting variations up to about an inch in a single pour. For floors with large structural heaves, broken sections, or significant vertical displacement, concrete repair is the right starting point before any overlay is considered.

  • How much floor prep is needed before you pour the overlay?

    Prep covers three steps: mechanical grinding to open the slab surface, degreasing to remove oils and curing compounds, and filling any cracks or voids. Every job uses a documented surface-prep checklist. Skipping or rushing any of these steps is the primary reason overlays fail prematurely.

  • Which areas do you cover for Self-Leveling Concrete Overlay?

    We cover Self-Leveling Concrete Overlay in and around Marietta, including Downtown Marietta, Cobb County, Atlanta, Fulton County and Cobb County. If your area isn’t listed, send us a quick message to check.

Get an Itemized Estimate for Your Floor

Tell us about the slab and we’ll schedule an assessment and quote materials, layer thickness, and cure times in writing.

Request Your Estimate